G.INP Query

[craiga79]

I too am on an ECI cab with G.INP enabled, using 8800NL. Can you post a link to 2.32d.dm2 please billion_fan.

Out of curiosity, has your interleave depth changed to 4 or 8 and INP at 48?

I've seen some posts elsewhere saying G.INP has been applied with interleave depth of 1 and INP at 48. Mine is at sitting with interleave of 1 and G.IMP of 52 and I can''t work out if G.INP is on or off due to the banding that 2.32e caused me (stuck at 44 down).

[underzone]

My FEC error bursts now seem resolved. I updated about 6pm yesterday:

[Rolacka]

I too am on an ECI cab with G.INP enabled, using 8800NL. Can you post a link to 2.32d.dm2 please billion_fan.

Out of curiosity, has your interleave depth changed to 4 or 8 and INP at 48?

I've seen some posts elsewhere saying G.INP has been applied with interleave depth of 1 and INP at 48. Mine is at sitting with interleave of 1 and G.IMP of 52 and I can''t work out if G.INP is on or off due to the banding that 2.32e caused me (stuck at 44 down).

Easy way to tell if g.inp is active is with dslstats the stats page gives you the info mine is below,

Stats recorded 07 Apr 2016 10:47:02

DSLAM/MSAN type: BDCM:0xa48c / v0xa48c
Modem/router firmware: AnnexA version - A2pv6F038j.d24h
DSL mode: VDSL2 Profile 17a
Status: Showtime
Uptime: 12 hours 17 min 23 sec
Resyncs: 0 (since 07 Apr 2016 10:46:44)

Downstream Upstream
Line attenuation (dB): 0.0 0.0
Signal attenuation (dB): Not monitored
Connection speed (kbps): 62975 19999
SNR margin (dB): 5.9 7.3
Power (dBm): 12.6 7.6
Interleave depth: 8 1
INP: 49.00 0
G.INP: Enabled Not enabled
Vectoring status: 5 (VECT_UNCONFIGURED)

RSCorr/RS (%): 0.0004 0.0018
RSUnCorr/RS (%): 0.0000 0.0000
ES/hour: 0 0

Homepage for dslstats is http://www.s446074245.websitehome.co.uk/

[craiga79]

I too am on an ECI cab with G.INP enabled, using 8800NL. Can you post a link to 2.32d.dm2 please billion_fan.

Out of curiosity, has your interleave depth changed to 4 or 8 and INP at 48?

I've seen some posts elsewhere saying G.INP has been applied with interleave depth of 1 and INP at 48. Mine is at sitting with interleave of 1 and G.IMP of 52 and I can''t work out if G.INP is on or off due to the banding that 2.32e caused me (stuck at 44 down).

Easy way to tell if g.inp is active is with dslstats the stats page gives you the info mine is below,

Stats recorded 07 Apr 2016 10:47:02

DSLAM/MSAN type: BDCM:0xa48c / v0xa48c
Modem/router firmware: AnnexA version - A2pv6F038j.d24h
DSL mode: VDSL2 Profile 17a
Status: Showtime
Uptime: 12 hours 17 min 23 sec
Resyncs: 0 (since 07 Apr 2016 10:46:44)

Downstream Upstream
Line attenuation (dB): 0.0 0.0
Signal attenuation (dB): Not monitored
Connection speed (kbps): 62975 19999
SNR margin (dB): 5.9 7.3
Power (dBm): 12.6 7.6
Interleave depth: 8 1
INP: 49.00 0
G.INP: Enabled Not enabled
Vectoring status: 5 (VECT_UNCONFIGURED)

RSCorr/RS (%): 0.0004 0.0018
RSUnCorr/RS (%): 0.0000 0.0000
ES/hour: 0 0

Homepage for dslstats is http://www.s446074245.websitehome.co.uk/

Perfect, thanks.

Seems I do have G.INP enabled with an interleave depth of 1 and INP at 52. Now for the waiting game to get the banding removed and get back to full speed.........

Downstream Upstream
Line attenuation (dB): 0.0 0.0
Signal attenuation (dB): Not monitored
Connection speed (kbps): 43998 15841
SNR margin (dB): 8.5 6.0
Power (dBm): 13.0 6.8
Interleave depth: 1 1
INP: 52.00 0
G.INP: Enabled Not enabled

RSCorr/RS (%): 35.9520 0.0111
RSUnCorr/RS (%): 0.0000 0.0000
ES/hour: 0 0.04

[Skyeci]

I hope this will help my 8800nl. I had g.inp for about a week on my eci cab/line but now its gone with a drop in sync and 8ms delay on the ds...
Fingers crossed it will help.