Billion UK Forum

Hi,

Purchased a Billion 8800NL about two weeks ago to replace a Home Hub 5 for BT VDSL. Pretty pleased with the added features but I cannot seem to get a solid connection and the device seems to reset around once a day. The logs always seem to revert to the 1st of Jan 00:00 and don't seem to provide any information about the event that seems to cause a reboot (I'm not sure that It is actually rebooting). Is it normal for this to happen? I've included a copy of the logs, the summary and the statistics for my line. If I have missed anything that would help please do ask. I have been hoping for my interleaving to be reduced and potentially for my speed to increase but I can't see that happening while the router is unable to keep connection consistently.

Any help much appreciated!

Logs:

Jan 1 00:00:15 kern warn kernel: bcmxtmcfg: bcmxtmcfg_init entry
Jan 1 00:00:15 kern warn kernel: adsl: adsl_init entry
Jan 1 00:00:15 kern warn kernel: Broadcom BCM63381B0 Ethernet Network Device v0.1 Dec 22 2016 13:42:48
Jan 1 00:00:15 kern warn kernel: ETH Init: Ch:0 - 200 tx BDs at 0xa2bd2000
Jan 1 00:00:15 kern warn kernel: ETH Init: Ch:0 - 1997 rx BDs at 0xa2ac4000
Jan 1 00:00:15 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
Jan 1 00:00:15 kern warn kernel: eth0: <Int sw port: 0> <Logical : 00> PHY_ID <0x00000001 : 0x01> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth1: <Int sw port: 1> <Logical : 01> PHY_ID <0x00000002 : 0x02> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth2: <Int sw port: 2> <Logical : 02> PHY_ID <0x00000003 : 0x03> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth3: <Int sw port: 3> <Logical : 03> PHY_ID <0x00000004 : 0x04> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth4: <Int sw port: 4> <Logical : 04> PHY_ID <0x05980018 : 0x18> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: Ethernet Auto Power Down and Sleep: Enabled
Jan 1 00:00:15 kern warn kernel: All Port Bit Map: 0x001f: eth0,eth1,eth2,eth3,eth4
Jan 1 00:00:15 kern warn kernel: Chip WAN Only Ports 0000, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0000:
Jan 1 00:00:15 kern warn kernel: Chip WAN Preffered Ports 0000, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0000:
Jan 1 00:00:15 kern warn kernel: Chip LAN Only Ports 0000, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0000:
Jan 1 00:00:15 kern warn kernel: WAN/LAN Both Capable Ports 0x001f:eth0,eth1,eth2,eth3,eth4
Jan 1 00:00:15 kern info kernel: NComm TMS V6.80 Kernel Module loaded.
Jan 1 00:00:15 kern warn kernel: --SMP support
Jan 1 00:00:15 kern warn kernel: wl: dsl_tx_pkt_flush_len=338
Jan 1 00:00:15 kern warn kernel: wl: norm_wmark_tot=1417, pktc_wmark_tot=1417
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jan 1 00:00:15 kern warn kernel: wl: passivemode=1
Jan 1 00:00:15 kern info kernel: wl0: creating kthread wl0-kthrd
Jan 1 00:00:15 kern warn kernel: wl: napimode=0
Jan 1 00:00:15 kern warn kernel: initvars_cis_pci: Not CIS format
Jan 1 00:00:15 kern warn kernel: Neither SPROM nor OTP has valid image
Jan 1 00:00:15 kern warn kernel: wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
Jan 1 00:00:15 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:15 kern warn kernel: wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
Jan 1 00:00:15 kern warn kernel: wl0: allocskbmode=1 currallocskbsz=256
Jan 1 00:00:15 kern warn kernel: wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.131.1608.cpe4.16L05.0-kdb
Jan 1 00:00:15 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Jan 1 00:00:15 kern info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: EHCI Host Controller
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
Jan 1 00:00:15 kern warn kernel: ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: irq 113, io mem 0x1000c300
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
Jan 1 00:00:15 kern info kernel: hub 1-0:1.0: USB hub found
Jan 1 00:00:15 kern info kernel: hub 1-0:1.0: 1 port detected
Jan 1 00:00:15 kern info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: OHCI Host Controller
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: irq 112, io mem 0x1000c400
Jan 1 00:00:15 kern info kernel: hub 2-0:1.0: USB hub found
Jan 1 00:00:15 kern info kernel: hub 2-0:1.0: 1 port detected
Jan 1 00:00:15 kern info kernel: usbcore: registered new interface driver usblp
Jan 1 00:00:15 kern info kernel: Broadcom 802.1Q VLAN Interface, v0.1
Jan 1 00:00:15 kern warn kernel: brcm_otp_init entry
Jan 1 00:00:15 kern warn kernel: Host MIPS Clock divider pwrsaving is enabled
Jan 1 00:00:15 kern info kernel: Netfilter messages via NETLINK v0.30.
Jan 1 00:00:16 kern warn kernel: br_netlink_mcpd.c: Setting registration type 0 pid to 431
Jan 1 00:00:16 kern info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:16 kern info kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:17 kern info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:17 kern info kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 1 00:00:20 kern info kernel: device eth1 entered promiscuous mode
Jan 1 00:00:20 kern info kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 1 00:00:24 kern info kernel: device eth2 entered promiscuous mode
Jan 1 00:00:24 kern info kernel: ADDRCONF(NETDEV_UP): eth2: link is not ready
Jan 1 00:00:27 kern info kernel: device eth3 entered promiscuous mode
Jan 1 00:00:27 kern info kernel: ADDRCONF(NETDEV_UP): eth3: link is not ready
Jan 1 00:00:30 kern info kernel: device eth4 entered promiscuous mode
Jan 1 00:00:30 kern info kernel: ADDRCONF(NETDEV_UP): eth4: link is not ready
Jan 1 00:00:33 kern warn kernel: *** dslThread dslPid=893
Jan 1 00:00:33 kern warn kernel: BcmAdsl_Initialize=0xC01AD050, g_pFnNotifyCallback=0xC01E8B60
Jan 1 00:00:33 kern warn kernel: DYING GASP IRQ Disabled
Jan 1 00:00:33 kern warn kernel: DYING GASP IRQ Enabled
Jan 1 00:00:33 kern warn kernel: AdslCoreSetSdramImageAddr: lmem2(0xce000) vs ADSL_PHY_SDRAM_BIAS(0xce000); origAddr=0xA3ECE000 newAddr=0xA3ECE000
Jan 1 00:00:33 kern warn kernel: pSdramPHY=0xA3FFFFF8, 0x1B777E 0xDEADBEEF
Jan 1 00:00:33 kern warn kernel: *** XfaceOffset: 0x4FF90 => 0x4FF90 ***
Jan 1 00:00:34 kern warn kernel: *** PhySdramSize got adjusted: 0xF5FB4 => 0x129AB8 ***
Jan 1 00:00:34 kern warn kernel: AdslCoreSharedMemInit: shareMemSize=34080(34080)
Jan 1 00:00:34 kern warn kernel: AdslCoreHwReset: pLocSbSta=80640000 bkupThreshold=3072
Jan 1 00:00:34 kern warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xA3FB59A4, time=10 ms
Jan 1 00:00:34 kern warn kernel: VersionInfo: A2pvI042j1.d26m
Jan 1 00:00:34 kern warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:34 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Jan 1 00:00:34 kern warn kernel: XTM Init: Ch:0 - 499 rx BDs at 0xa0e86000
Jan 1 00:00:34 kern warn kernel: XTM Init: Ch:1 - 16 rx BDs at 0xa3b56280
Jan 1 00:00:34 kern warn kernel: bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize(). Recovering.
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 8050b518
Jan 1 00:00:34 kern info kernel: nf_conntrack version 0.5.0 (917 buckets, 3668 max)
Jan 1 00:00:36 kern info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:36 kern info kernel: message received before monitor task is initialized kerSysSendtoMonitorTask
Jan 1 00:00:37 kern info kernel: monitor task is initialized pid= 378
Jan 1 00:00:40 kern warn kernel: Energy Efficient Ethernet: Enabled
Jan 1 00:00:42 user info syslog: WLAN Schedule Control on wl0 exit
Jan 1 00:00:44 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:00:44 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
Jan 1 00:00:45 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:00:45 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:00:59 kern crit kernel: Line 0: VDSL G.993 channel analysis
Jan 1 00:01:00 kern crit kernel: Line 0: VDSL2 link up, Bearer 0, us=6703, ds=35000
Jan 1 00:01:00 kern crit kernel: Line 0: VDSL2 link up, Bearer 1, us=0, ds=0
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: SILI Start - UtopiaCfg - 0
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = ENABLED
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = PTM(2)
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: SILI End - UtopiaCfg - 10
Jan 1 00:01:00 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Jan 1 00:01:00 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e d5 23
Jan 1 00:01:00 kern warn kernel: [DoCreateDeviceReq.775]: register_netdev
Jan 1 00:01:00 kern warn kernel: [DoCreateDeviceReq.777]: register_netdev done
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jan 1 00:01:00 kern warn kernel: NON-CO4 DSLAM based operations for PTM CRC & ENET FCS.
Jan 1 00:01:00 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa176a000
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=6703000, DS=35000000
Jan 1 00:01:01 kern warn kernel: ptm0.1 MAC address set to 60:03:47:2E:D5:24
Jan 1 00:01:01 kern warn kernel: netdev path : ptm0.1
Jan 1 00:01:01 kern info kernel: ->
Jan 1 00:01:01 kern info kernel: ptm0
Jan 1 00:01:01 kern warn kernel: BCMVLAN : ptm0 mode was set to RG
Jan 1 00:01:01 kern info kernel: device ptm0 entered promiscuous mode
Jan 1 00:01:01 daemon notice syslog: pppd:cms logging initialized.
Jan 1 00:01:01 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jan 1 00:01:01 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:24 daemon err syslog: pppd:Couldn't get channel number: Transport endpoint is not connected
Jan 1 00:01:24 daemon notice syslog: pppd:Couldn't reset tty to normal line discipline: Inappropriate ioctl for device
Jan 1 00:01:24 daemon notice syslog: pppd:Doing disconnect
Jan 1 00:01:27 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:27 daemon crit syslog: PPP server detected.
Jan 1 00:01:27 daemon crit syslog: PPP session established.
Jan 1 00:01:27 kern warn kernel: netdev path : ppp1.1
Jan 1 00:01:27 kern info kernel: ->
Jan 1 00:01:27 kern info kernel: ptm0.1
Jan 1 00:01:27 daemon notice syslog: pppd:Using interface ppp1.1
Jan 1 00:01:27 kern info kernel: -> ptm0
Jan 1 00:01:27 daemon notice syslog: pppd:Connect: ppp1.1 <--> ptm0.1
Jan 1 00:01:27 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jan 1 00:01:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:27 daemon crit syslog: PPP LCP UP.
Jan 1 00:01:27 daemon notice syslog: pppd:Warning - secret file /etc/ppp/chap-secrets has world and/or group access
Jan 1 00:01:27 daemon notice syslog: pppd:No CHAP secret found for authenticating us to acc-aln6.tw
Jan 1 00:01:27 daemon notice syslog: pppd:Remote message: CHAP authentication success
Jan 1 00:01:27 daemon notice syslog: pppd:local IP address 86.133.12.39
Jan 1 00:01:27 daemon notice syslog: pppd:remote IP address 172.16.10.5
Jan 1 00:01:27 daemon notice syslog: pppd:primary DNS address 81.139.56.100
Jan 1 00:01:27 daemon notice syslog: pppd:secondary DNS address 81.139.57.100
Jan 1 00:01:27 daemon crit syslog: Received valid IP address from server. Connection UP.
Jan 1 00:01:28 user info syslog: ddnsd: xxxxxx.ddns.net (ppp1.1) IP has changed from (null) to 86.133.12.39
Jan 1 00:01:28 user info syslog: ddnsd: update xxxxxx.ddns.net request failed. Please check the setting.
Jan 1 00:01:38 user info syslog: ddnsd: xxxxxx.ddns.net (ppp1.1) IP has changed from (null) to 86.133.12.39
Jan 1 00:01:39 user info syslog: ddnsd: update xxxxxx.ddns.net request successfully
Mar 1 12:13:48 kern warn kernel: upnp/1645: potentially unexpected fatal signal 11.
Mar 1 12:13:48 kern warn kernel: Cpu 0
Mar 1 12:13:48 kern warn kernel: $ 0 :
Mar 1 12:13:48 kern info kernel: 00000000 10008d00 00000000
Mar 1 12:13:48 kern info kernel: 0042ca21
Mar 1 12:13:48 kern warn kernel: $ 4 : ffffffff
Mar 1 12:13:48 kern info kernel: 00419130 00000057
Mar 1 12:13:48 kern info kernel: 0042ca22
Mar 1 12:13:48 kern warn kernel: $ 8 : 00417126
Mar 1 12:13:48 kern info kernel: 00000070 00000031
Mar 1 12:13:48 kern info kernel: 0086d051
Mar 1 12:13:48 kern warn kernel: $12 : 502d454e
Mar 1 12:13:48 kern info kernel: 830ab8e9
Mar 1 12:13:48 kern info kernel: 7474703a 2f2f7363
Mar 1 12:13:48 kern warn kernel: $16 : 0086cc7c
Mar 1 12:13:48 kern info kernel: 00000000
Mar 1 12:13:48 kern info kernel: 0086cf1a 0086cf1a
Mar 1 12:13:48 kern warn kernel: $20 : 0086bafc
Mar 1 12:13:48 kern info kernel: 0086cf43
Mar 1 12:13:48 kern info kernel: 0041a9b0 00420000
Mar 1 12:13:48 kern warn kernel: $24 : 00000003
Mar 1 12:13:48 kern info kernel: 76f7adf0
Mar 1 12:13:48 kern info kernel:
Mar 1 12:13:48 kern warn kernel: $28 : 00434260
Mar 1 12:13:48 kern info kernel: 7fb63978
Mar 1 12:13:48 kern info kernel: 0086cf39 00411404
Mar 1 12:13:48 kern warn kernel: Hi : 00000000
Mar 1 12:13:48 kern warn kernel: Lo : 00000140
Mar 1 12:13:48 kern warn kernel: epc : 76f7ae0c 0x76f7ae0c
Mar 1 12:13:48 kern warn kernel: Tainted: P
Mar 1 12:13:48 kern warn kernel: ra : 00411404 0x411404
Mar 1 12:13:48 kern warn kernel: Status: 00008d13
Mar 1 12:13:48 kern info kernel: USER
Mar 1 12:13:48 kern info kernel: EXL IE
Mar 1 12:13:48 kern warn kernel: Cause : 00000008
Mar 1 12:13:48 kern warn kernel: BadVA : 00000000
Mar 1 12:13:48 kern warn kernel: PrId : 0002a081 (Broadcom BMIPS4350)

snowlucas wrote:Hi,

Purchased a Billion 8800NL about two weeks ago to replace a Home Hub 5 for BT VDSL. Pretty pleased with the added features but I cannot seem to get a solid connection and the device seems to reset around once a day. The logs always seem to revert to the 1st of Jan 00:00 and don't seem to provide any information about the event that seems to cause a reboot (I'm not sure that It is actually rebooting). Is it normal for this to happen? I've included a copy of the logs, the summary and the statistics for my line. If I have missed anything that would help please do ask. I have been hoping for my interleaving to be reduced and potentially for my speed to increase but I can't see that happening while the router is unable to keep connection consistently.

Any help much appreciated!

Logs:

Jan 1 00:00:15 kern warn kernel: bcmxtmcfg: bcmxtmcfg_init entry
Jan 1 00:00:15 kern warn kernel: adsl: adsl_init entry
Jan 1 00:00:15 kern warn kernel: Broadcom BCM63381B0 Ethernet Network Device v0.1 Dec 22 2016 13:42:48
Jan 1 00:00:15 kern warn kernel: ETH Init: Ch:0 - 200 tx BDs at 0xa2bd2000
Jan 1 00:00:15 kern warn kernel: ETH Init: Ch:0 - 1997 rx BDs at 0xa2ac4000
Jan 1 00:00:15 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
Jan 1 00:00:15 kern warn kernel: eth0: <Int sw port: 0> <Logical : 00> PHY_ID <0x00000001 : 0x01> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth1: <Int sw port: 1> <Logical : 01> PHY_ID <0x00000002 : 0x02> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth2: <Int sw port: 2> <Logical : 02> PHY_ID <0x00000003 : 0x03> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth3: <Int sw port: 3> <Logical : 03> PHY_ID <0x00000004 : 0x04> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth4: <Int sw port: 4> <Logical : 04> PHY_ID <0x05980018 : 0x18> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: Ethernet Auto Power Down and Sleep: Enabled
Jan 1 00:00:15 kern warn kernel: All Port Bit Map: 0x001f: eth0,eth1,eth2,eth3,eth4
Jan 1 00:00:15 kern warn kernel: Chip WAN Only Ports 0000, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0000:
Jan 1 00:00:15 kern warn kernel: Chip WAN Preffered Ports 0000, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0000:
Jan 1 00:00:15 kern warn kernel: Chip LAN Only Ports 0000, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0000:
Jan 1 00:00:15 kern warn kernel: WAN/LAN Both Capable Ports 0x001f:eth0,eth1,eth2,eth3,eth4
Jan 1 00:00:15 kern info kernel: NComm TMS V6.80 Kernel Module loaded.
Jan 1 00:00:15 kern warn kernel: --SMP support
Jan 1 00:00:15 kern warn kernel: wl: dsl_tx_pkt_flush_len=338
Jan 1 00:00:15 kern warn kernel: wl: norm_wmark_tot=1417, pktc_wmark_tot=1417
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jan 1 00:00:15 kern warn kernel: wl: passivemode=1
Jan 1 00:00:15 kern info kernel: wl0: creating kthread wl0-kthrd
Jan 1 00:00:15 kern warn kernel: wl: napimode=0
Jan 1 00:00:15 kern warn kernel: initvars_cis_pci: Not CIS format
Jan 1 00:00:15 kern warn kernel: Neither SPROM nor OTP has valid image
Jan 1 00:00:15 kern warn kernel: wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
Jan 1 00:00:15 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:15 kern warn kernel: wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
Jan 1 00:00:15 kern warn kernel: wl0: allocskbmode=1 currallocskbsz=256
Jan 1 00:00:15 kern warn kernel: wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.131.1608.cpe4.16L05.0-kdb
Jan 1 00:00:15 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Jan 1 00:00:15 kern info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: EHCI Host Controller
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
Jan 1 00:00:15 kern warn kernel: ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: irq 113, io mem 0x1000c300
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
Jan 1 00:00:15 kern info kernel: hub 1-0:1.0: USB hub found
Jan 1 00:00:15 kern info kernel: hub 1-0:1.0: 1 port detected
Jan 1 00:00:15 kern info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: OHCI Host Controller
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: irq 112, io mem 0x1000c400
Jan 1 00:00:15 kern info kernel: hub 2-0:1.0: USB hub found
Jan 1 00:00:15 kern info kernel: hub 2-0:1.0: 1 port detected
Jan 1 00:00:15 kern info kernel: usbcore: registered new interface driver usblp
Jan 1 00:00:15 kern info kernel: Broadcom 802.1Q VLAN Interface, v0.1
Jan 1 00:00:15 kern warn kernel: brcm_otp_init entry
Jan 1 00:00:15 kern warn kernel: Host MIPS Clock divider pwrsaving is enabled
Jan 1 00:00:15 kern info kernel: Netfilter messages via NETLINK v0.30.
Jan 1 00:00:16 kern warn kernel: br_netlink_mcpd.c: Setting registration type 0 pid to 431
Jan 1 00:00:16 kern info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:16 kern info kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:17 kern info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:17 kern info kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 1 00:00:20 kern info kernel: device eth1 entered promiscuous mode
Jan 1 00:00:20 kern info kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 1 00:00:24 kern info kernel: device eth2 entered promiscuous mode
Jan 1 00:00:24 kern info kernel: ADDRCONF(NETDEV_UP): eth2: link is not ready
Jan 1 00:00:27 kern info kernel: device eth3 entered promiscuous mode
Jan 1 00:00:27 kern info kernel: ADDRCONF(NETDEV_UP): eth3: link is not ready
Jan 1 00:00:30 kern info kernel: device eth4 entered promiscuous mode
Jan 1 00:00:30 kern info kernel: ADDRCONF(NETDEV_UP): eth4: link is not ready
Jan 1 00:00:33 kern warn kernel: *** dslThread dslPid=893
Jan 1 00:00:33 kern warn kernel: BcmAdsl_Initialize=0xC01AD050, g_pFnNotifyCallback=0xC01E8B60
Jan 1 00:00:33 kern warn kernel: DYING GASP IRQ Disabled
Jan 1 00:00:33 kern warn kernel: DYING GASP IRQ Enabled
Jan 1 00:00:33 kern warn kernel: AdslCoreSetSdramImageAddr: lmem2(0xce000) vs ADSL_PHY_SDRAM_BIAS(0xce000); origAddr=0xA3ECE000 newAddr=0xA3ECE000
Jan 1 00:00:33 kern warn kernel: pSdramPHY=0xA3FFFFF8, 0x1B777E 0xDEADBEEF
Jan 1 00:00:33 kern warn kernel: *** XfaceOffset: 0x4FF90 => 0x4FF90 ***
Jan 1 00:00:34 kern warn kernel: *** PhySdramSize got adjusted: 0xF5FB4 => 0x129AB8 ***
Jan 1 00:00:34 kern warn kernel: AdslCoreSharedMemInit: shareMemSize=34080(34080)
Jan 1 00:00:34 kern warn kernel: AdslCoreHwReset: pLocSbSta=80640000 bkupThreshold=3072
Jan 1 00:00:34 kern warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xA3FB59A4, time=10 ms
Jan 1 00:00:34 kern warn kernel: VersionInfo: A2pvI042j1.d26m
Jan 1 00:00:34 kern warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:34 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Jan 1 00:00:34 kern warn kernel: XTM Init: Ch:0 - 499 rx BDs at 0xa0e86000
Jan 1 00:00:34 kern warn kernel: XTM Init: Ch:1 - 16 rx BDs at 0xa3b56280
Jan 1 00:00:34 kern warn kernel: bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize(). Recovering.
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 8050b518
Jan 1 00:00:34 kern info kernel: nf_conntrack version 0.5.0 (917 buckets, 3668 max)
Jan 1 00:00:36 kern info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:36 kern info kernel: message received before monitor task is initialized kerSysSendtoMonitorTask
Jan 1 00:00:37 kern info kernel: monitor task is initialized pid= 378
Jan 1 00:00:40 kern warn kernel: Energy Efficient Ethernet: Enabled
Jan 1 00:00:42 user info syslog: WLAN Schedule Control on wl0 exit
Jan 1 00:00:44 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:00:44 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
Jan 1 00:00:45 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:00:45 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:00:59 kern crit kernel: Line 0: VDSL G.993 channel analysis
Jan 1 00:01:00 kern crit kernel: Line 0: VDSL2 link up, Bearer 0, us=6703, ds=35000
Jan 1 00:01:00 kern crit kernel: Line 0: VDSL2 link up, Bearer 1, us=0, ds=0
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: SILI Start - UtopiaCfg - 0
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = ENABLED
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = PTM(2)
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: SILI End - UtopiaCfg - 10
Jan 1 00:01:00 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Jan 1 00:01:00 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e d5 23
Jan 1 00:01:00 kern warn kernel: [DoCreateDeviceReq.775]: register_netdev
Jan 1 00:01:00 kern warn kernel: [DoCreateDeviceReq.777]: register_netdev done
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jan 1 00:01:00 kern warn kernel: NON-CO4 DSLAM based operations for PTM CRC & ENET FCS.
Jan 1 00:01:00 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa176a000
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=6703000, DS=35000000
Jan 1 00:01:01 kern warn kernel: ptm0.1 MAC address set to 60:03:47:2E:D5:24
Jan 1 00:01:01 kern warn kernel: netdev path : ptm0.1
Jan 1 00:01:01 kern info kernel: ->
Jan 1 00:01:01 kern info kernel: ptm0
Jan 1 00:01:01 kern warn kernel: BCMVLAN : ptm0 mode was set to RG
Jan 1 00:01:01 kern info kernel: device ptm0 entered promiscuous mode
Jan 1 00:01:01 daemon notice syslog: pppd:cms logging initialized.
Jan 1 00:01:01 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jan 1 00:01:01 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:24 daemon err syslog: pppd:Couldn't get channel number: Transport endpoint is not connected
Jan 1 00:01:24 daemon notice syslog: pppd:Couldn't reset tty to normal line discipline: Inappropriate ioctl for device
Jan 1 00:01:24 daemon notice syslog: pppd:Doing disconnect
Jan 1 00:01:27 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:27 daemon crit syslog: PPP server detected.
Jan 1 00:01:27 daemon crit syslog: PPP session established.
Jan 1 00:01:27 kern warn kernel: netdev path : ppp1.1
Jan 1 00:01:27 kern info kernel: ->
Jan 1 00:01:27 kern info kernel: ptm0.1
Jan 1 00:01:27 daemon notice syslog: pppd:Using interface ppp1.1
Jan 1 00:01:27 kern info kernel: -> ptm0
Jan 1 00:01:27 daemon notice syslog: pppd:Connect: ppp1.1 <--> ptm0.1
Jan 1 00:01:27 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jan 1 00:01:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:27 daemon crit syslog: PPP LCP UP.
Jan 1 00:01:27 daemon notice syslog: pppd:Warning - secret file /etc/ppp/chap-secrets has world and/or group access
Jan 1 00:01:27 daemon notice syslog: pppd:No CHAP secret found for authenticating us to acc-aln6.tw
Jan 1 00:01:27 daemon notice syslog: pppd:Remote message: CHAP authentication success
Jan 1 00:01:27 daemon notice syslog: pppd:local IP address 86.133.12.39
Jan 1 00:01:27 daemon notice syslog: pppd:remote IP address 172.16.10.5
Jan 1 00:01:27 daemon notice syslog: pppd:primary DNS address 81.139.56.100
Jan 1 00:01:27 daemon notice syslog: pppd:secondary DNS address 81.139.57.100
Jan 1 00:01:27 daemon crit syslog: Received valid IP address from server. Connection UP.
Jan 1 00:01:28 user info syslog: ddnsd: xxxxxx.ddns.net (ppp1.1) IP has changed from (null) to 86.133.12.39
Jan 1 00:01:28 user info syslog: ddnsd: update xxxxxx.ddns.net request failed. Please check the setting.
Jan 1 00:01:38 user info syslog: ddnsd: xxxxxx.ddns.net (ppp1.1) IP has changed from (null) to 86.133.12.39
Jan 1 00:01:39 user info syslog: ddnsd: update xxxxxx.ddns.net request successfully
Mar 1 12:13:48 kern warn kernel: upnp/1645: potentially unexpected fatal signal 11.
Mar 1 12:13:48 kern warn kernel: Cpu 0
Mar 1 12:13:48 kern warn kernel: $ 0 :
Mar 1 12:13:48 kern info kernel: 00000000 10008d00 00000000
Mar 1 12:13:48 kern info kernel: 0042ca21
Mar 1 12:13:48 kern warn kernel: $ 4 : ffffffff
Mar 1 12:13:48 kern info kernel: 00419130 00000057
Mar 1 12:13:48 kern info kernel: 0042ca22
Mar 1 12:13:48 kern warn kernel: $ 8 : 00417126
Mar 1 12:13:48 kern info kernel: 00000070 00000031
Mar 1 12:13:48 kern info kernel: 0086d051
Mar 1 12:13:48 kern warn kernel: $12 : 502d454e
Mar 1 12:13:48 kern info kernel: 830ab8e9
Mar 1 12:13:48 kern info kernel: 7474703a 2f2f7363
Mar 1 12:13:48 kern warn kernel: $16 : 0086cc7c
Mar 1 12:13:48 kern info kernel: 00000000
Mar 1 12:13:48 kern info kernel: 0086cf1a 0086cf1a
Mar 1 12:13:48 kern warn kernel: $20 : 0086bafc
Mar 1 12:13:48 kern info kernel: 0086cf43
Mar 1 12:13:48 kern info kernel: 0041a9b0 00420000
Mar 1 12:13:48 kern warn kernel: $24 : 00000003
Mar 1 12:13:48 kern info kernel: 76f7adf0
Mar 1 12:13:48 kern info kernel:
Mar 1 12:13:48 kern warn kernel: $28 : 00434260
Mar 1 12:13:48 kern info kernel: 7fb63978
Mar 1 12:13:48 kern info kernel: 0086cf39 00411404
Mar 1 12:13:48 kern warn kernel: Hi : 00000000
Mar 1 12:13:48 kern warn kernel: Lo : 00000140
Mar 1 12:13:48 kern warn kernel: epc : 76f7ae0c 0x76f7ae0c
Mar 1 12:13:48 kern warn kernel: Tainted: P
Mar 1 12:13:48 kern warn kernel: ra : 00411404 0x411404
Mar 1 12:13:48 kern warn kernel: Status: 00008d13
Mar 1 12:13:48 kern info kernel: USER
Mar 1 12:13:48 kern info kernel: EXL IE
Mar 1 12:13:48 kern warn kernel: Cause : 00000008
Mar 1 12:13:48 kern warn kernel: BadVA : 00000000
Mar 1 12:13:48 kern warn kernel: PrId : 0002a081 (Broadcom BMIPS4350)

On your system log I noticed a UPNP crash.

Please try the following

1. Login to the router
2. Click on 'Advanced Setup >> UPNP'
3. Disable the UPNP function and click on 'Apply'
4. Monitor the router over the next 2 days and see if it reboots

Thanks for the quick response.

I have done this and see if it fixes the issue over the next few days. If it is due to UPNP then is the most likely cause something on my network using UPNP incorrectly or is there any history of this issue with the router itself? Obviously I would prefer UPNP to be enabled... I guess I'm jumping ahead of myself a little.

Thanks again.

snowlucas wrote:Thanks for the quick response.

I have done this and see if it fixes the issue over the next few days. If it is due to UPNP then is the most likely cause something on my network using UPNP incorrectly or is there any history of this issue with the router itself? Obviously I would prefer UPNP to be enabled... I guess I'm jumping ahead of myself a little.

Thanks again.

Lets wait and see if the issue is related the UPNP service, I haven't seen a UPNP crash on the newer 2.52.d1 firmware yet, (but normally this kind of crash is related to the router)

If turning off UPNP does not resolve the issue, you might need to setup a sys log server on a windows based machine to capture the logs before the device reboots, so we can get a indication of what the issue might be

Ok makes sense.

What is interesting is I actually have another 8800NL that I set up in France on ADSL2+ last week which has had a similar issue with seemingly rebooting. If the log starts with jan 1 00:00 is that definitive evidence that the router rebooted? Some parts of the setup are entirely different (ADSL vs VDSL) but its the same firmware, has very similar devices running on its network and updates a dynamic DNS.

Don't want to confuse the thread but as it seems to have the same issue I've added some information from this 2nd router below.
Logs below are from this other router:

Jan 1 00:00:34 kern warn kernel: AdslCoreSharedMemInit: shareMemSize=34080(34080)
Jan 1 00:00:34 kern warn kernel: AdslCoreHwReset: pLocSbSta=806e0000 bkupThreshold=3072
Jan 1 00:00:34 kern warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xA3FB59A4, time=11 ms
Jan 1 00:00:34 kern warn kernel: VersionInfo: A2pvI042j1.d26m
Jan 1 00:00:34 kern warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:34 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Jan 1 00:00:34 kern warn kernel: XTM Init: Ch:0 - 499 rx BDs at 0xa0735000
Jan 1 00:00:34 kern warn kernel: XTM Init: Ch:1 - 16 rx BDs at 0xa0c10880
Jan 1 00:00:34 kern warn kernel: bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize(). Recovering.
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Jan 1 00:00:34 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 80c21518
Jan 1 00:00:34 kern info kernel: nf_conntrack version 0.5.0 (917 buckets, 3668 max)
Jan 1 00:00:36 kern info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:36 kern info kernel: message received before monitor task is initialized kerSysSendtoMonitorTask
Jan 1 00:00:37 kern info kernel: monitor task is initialized pid= 378
Jan 1 00:00:39 kern warn kernel: Energy Efficient Ethernet: Enabled
Jan 1 00:00:41 user info syslog: WLAN Schedule Control on wl0 exit
Jan 1 00:00:44 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:00:44 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
Jan 1 00:00:44 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:00:44 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:00:53 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link DOWN.
Jan 1 00:00:53 kern info kernel: br0: port 5(eth4) entered disabled state
Jan 1 00:00:57 kern crit kernel: Line 0: ADSL G.992 channel analysis
Jan 1 00:01:03 kern crit kernel: Line 0: ADSL G.992 message exchange
Jan 1 00:01:04 kern crit kernel: Line 0: ADSL link up, Bearer 0, us=1021, ds=10015
Jan 1 00:01:04 kern warn kernel: bcmxtmcfg: SILI Start - UtopiaCfg - 0
Jan 1 00:01:04 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Jan 1 00:01:04 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Jan 1 00:01:04 kern warn kernel: bcmxtmcfg: AutoSenseATM is not enabled. Link Traffic type from PHY=1
Jan 1 00:01:04 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = ATM(1)
Jan 1 00:01:04 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 1
Jan 1 00:01:04 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jan 1 00:01:04 kern warn kernel: bcmxtmcfg: SILI End - UtopiaCfg - 10
Jan 1 00:01:04 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Jan 1 00:01:04 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e d8 ab
Jan 1 00:01:04 kern warn kernel: [DoCreateDeviceReq.775]: register_netdev
Jan 1 00:01:05 kern warn kernel: [DoCreateDeviceReq.777]: register_netdev done
Jan 1 00:01:05 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jan 1 00:01:05 kern warn kernel: NON-CO4 DSLAM based operations for PTM CRC & ENET FCS.
Jan 1 00:01:05 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa1740000
Jan 1 00:01:05 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=1021000, DS=10015000
Jan 1 00:01:05 daemon notice syslog: pppd:cms logging initialized.
Jan 1 00:01:05 daemon notice syslog: pppd:PPPoATM setdevname_pppoatm
Jan 1 00:01:05 daemon notice syslog: pppd:PPPoATM setdevname_pppoatm - SUCCESS
Jan 1 00:01:05 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jan 1 00:01:05 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:05 kern warn kernel: netdev path : pppoa0
Jan 1 00:01:05 daemon notice syslog: pppd:Using interface pppoa0
Jan 1 00:01:05 daemon notice syslog: pppd:Connect: pppoa0 <-->
Jan 1 00:01:05 kern info kernel: ->
Jan 1 00:01:05 kern info kernel: atm0
Jan 1 00:01:05 daemon crit syslog: PPP LCP UP.
Jan 1 00:01:05 daemon notice syslog: pppd:Remote message: CHAP authentication success, unit 1394
Jan 1 00:01:05 daemon notice syslog: pppd:local IP address 78.112.241.240
Jan 1 00:01:05 daemon notice syslog: pppd:remote IP address 78.112.241.1
Jan 1 00:01:05 daemon notice syslog: pppd:primary DNS address 109.0.66.10
Jan 1 00:01:05 daemon notice syslog: pppd:secondary DNS address 109.0.66.20
Jan 1 00:01:05 daemon crit syslog: Received valid IP address from server. Connection UP.
Jan 1 00:01:06 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:01:06 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:06 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:07 user info syslog: ddnsd: xxxxx.ddns.net (pppoa0) IP has changed from (null) to 78.112.241.240
Jan 1 00:01:07 user info syslog: ddnsd: update xxxxx.ddns.net request failed. Please check the setting.
Feb 28 19:52:44 user info syslog: ddnsd: xxxxx.ddns.net (pppoa0) IP has changed from (null) to 78.112.241.240
Feb 28 19:52:45 user info syslog: ddnsd: update xxxxx.ddns.net request successfully
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: SILI Start - UtopiaCfg - 10
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: AutoSenseATM is not enabled. Link Traffic type from PHY=1
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN(2), Service Support = ATM(1)
Mar 1 15:15:38 kern warn kernel: HOST XTM tx ch 0 disabled.
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 0
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: SILI End - UtopiaCfg - 0
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Mar 1 15:15:38 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 80c21518
Mar 1 15:15:38 kern warn kernel: Warning: SAR Channel 0 Rx Bogus Event
Mar 1 15:15:41 daemon notice syslog: pppd:Terminating on signal 20.
Mar 1 15:15:41 daemon crit syslog: Clear IP addresses. PPP connection DOWN.
Mar 1 15:15:41 daemon crit syslog: Clear IP addresses. Connection DOWN.
Mar 1 15:16:01 kern crit kernel: Line 0: ADSL G.992 channel analysis
Mar 1 15:16:07 kern crit kernel: Line 0: ADSL G.992 message exchange
Mar 1 15:16:07 kern crit kernel: Line 0: ADSL link up, Bearer 0, us=1021, ds=10015
Mar 1 15:16:07 kern warn kernel: bcmxtmcfg: SILI Start - UtopiaCfg - 0
Mar 1 15:16:07 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Mar 1 15:16:07 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Mar 1 15:16:07 kern warn kernel: bcmxtmcfg: AutoSenseATM is not enabled. Link Traffic type from PHY=1
Mar 1 15:16:07 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = ATM(1)
Mar 1 15:16:07 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 1
Mar 1 15:16:07 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Mar 1 15:16:07 kern warn kernel: bcmxtmcfg: SILI End - UtopiaCfg - 10
Mar 1 15:16:08 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Mar 1 15:16:08 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e d8 ab
Mar 1 15:16:08 kern warn kernel: [DoCreateDeviceReq.775]: register_netdev
Mar 1 15:16:08 kern warn kernel: [DoCreateDeviceReq.777]: register_netdev done
Mar 1 15:16:08 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Mar 1 15:16:08 kern warn kernel: NON-CO4 DSLAM based operations for PTM CRC & ENET FCS.
Mar 1 15:16:08 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa18c6000
Mar 1 15:16:08 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=1021000, DS=10015000
Mar 1 15:16:08 daemon notice syslog: pppd:cms logging initialized.
Mar 1 15:16:08 daemon notice syslog: pppd:PPPoATM setdevname_pppoatm
Mar 1 15:16:08 daemon notice syslog: pppd:PPPoATM setdevname_pppoatm - SUCCESS
Mar 1 15:16:08 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Mar 1 15:16:08 daemon notice syslog: PPP: Start to connect ...
Mar 1 15:16:08 kern warn kernel: netdev path : pppoa0 ->
Mar 1 15:16:08 daemon notice syslog: pppd:Using interface pppoa0
Mar 1 15:16:08 daemon notice syslog: pppd:Connect: pppoa0 <-->
Mar 1 15:16:08 kern info kernel: atm0
Mar 1 15:16:08 daemon crit syslog: PPP LCP UP.
Mar 1 15:16:08 daemon notice syslog: pppd:Remote message: CHAP authentication success, unit 1394
Mar 1 15:16:08 daemon notice syslog: pppd:local IP address 78.112.241.199
Mar 1 15:16:08 daemon notice syslog: pppd:remote IP address 78.112.241.1
Mar 1 15:16:08 daemon notice syslog: pppd:primary DNS address 109.0.66.10
Mar 1 15:16:08 daemon notice syslog: pppd:secondary DNS address 109.0.66.20
Mar 1 15:16:08 daemon crit syslog: Received valid IP address from server. Connection UP.
Mar 1 15:16:13 user info syslog: ddnsd: togadere.ddns.net (pppoa0) IP has changed from 78.112.241.240 to 78.112.241.199
Mar 1 15:16:14 user info syslog: ddnsd: update togadere.ddns.net request successfully
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: SILI Start - UtopiaCfg - 10
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: AutoSenseATM is not enabled. Link Traffic type from PHY=1
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = DOWN(2), Service Support = ATM(1)
Mar 1 15:17:50 kern warn kernel: HOST XTM tx ch 0 disabled.
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 0
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: SILI End - UtopiaCfg - 0
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Mar 1 15:17:50 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 80c21518
Mar 1 15:17:50 kern warn kernel: Warning: SAR Channel 0 Rx Bogus Event
Mar 1 15:17:53 daemon notice syslog: pppd:Terminating on signal 20.
Mar 1 15:17:53 daemon crit syslog: Clear IP addresses. PPP connection DOWN.
Mar 1 15:17:53 daemon crit syslog: Clear IP addresses. Connection DOWN.
Mar 1 15:18:13 kern crit kernel: Line 0: ADSL G.992 channel analysis
Mar 1 15:18:19 kern crit kernel: Line 0: ADSL G.992 message exchange
Mar 1 15:18:42 kern crit kernel: Line 0: ADSL G.992 channel analysis
Mar 1 15:18:48 kern crit kernel: Line 0: ADSL link up, Bearer 0, us=1021, ds=9051
Mar 1 15:18:48 kern warn kernel: bcmxtmcfg: SILI Start - UtopiaCfg - 0
Mar 1 15:18:48 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Mar 1 15:18:48 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Mar 1 15:18:48 kern warn kernel: bcmxtmcfg: AutoSenseATM is not enabled. Link Traffic type from PHY=1
Mar 1 15:18:48 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = ATM(1)
Mar 1 15:18:48 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 1
Mar 1 15:18:48 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Mar 1 15:18:48 kern warn kernel: bcmxtmcfg: SILI End - UtopiaCfg - 10
Mar 1 15:18:49 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Mar 1 15:18:49 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e d8 ab
Mar 1 15:18:49 kern warn kernel: [DoCreateDeviceReq.775]: register_netdev
Mar 1 15:18:49 kern warn kernel: [DoCreateDeviceReq.777]: register_netdev done
Mar 1 15:18:49 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Mar 1 15:18:49 kern warn kernel: NON-CO4 DSLAM based operations for PTM CRC & ENET FCS.
Mar 1 15:18:49 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa19f4000
Mar 1 15:18:49 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=1021000, DS=9051000
Mar 1 15:18:49 daemon notice syslog: pppd:cms logging initialized.
Mar 1 15:18:49 daemon notice syslog: pppd:PPPoATM setdevname_pppoatm
Mar 1 15:18:49 daemon notice syslog: pppd:PPPoATM setdevname_pppoatm - SUCCESS
Mar 1 15:18:49 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Mar 1 15:18:49 daemon notice syslog: PPP: Start to connect ...
Mar 1 15:18:49 kern warn kernel: netdev path :
Mar 1 15:18:49 kern info kernel: pppoa0 ->
Mar 1 15:18:49 kern info kernel: atm0
Mar 1 15:18:49 daemon notice syslog: pppd:Using interface pppoa0
Mar 1 15:18:49 daemon notice syslog: pppd:Connect: pppoa0 <-->
Mar 1 15:18:49 daemon crit syslog: PPP LCP UP.
Mar 1 15:18:49 daemon notice syslog: pppd:Remote message: CHAP authentication success, unit 1394
Mar 1 15:18:49 daemon notice syslog: pppd:local IP address 78.112.94.115
Mar 1 15:18:49 daemon notice syslog: pppd:remote IP address 78.112.94.1
Mar 1 15:18:49 daemon notice syslog: pppd:primary DNS address 109.0.66.20
Mar 1 15:18:49 daemon notice syslog: pppd:secondary DNS address 109.0.66.10
Mar 1 15:18:49 daemon crit syslog: Received valid IP address from server. Connection UP.
Mar 1 15:18:55 user info syslog: ddnsd: xxxxx.ddns.net (pppoa0) IP has changed from 78.112.241.199 to 78.112.94.115
Mar 1 15:18:56 user info syslog: ddnsd: update xxxxx.ddns.net request successfully

It looks like we will need to perform the syslog capture, attached is guide on how to do so on a windows PC. (you must leave the sys log server open and running on PC to capture the logs locally)

A accurate way to tell if the router is rebooting is to check the 'System Up Time' on the status page of the router

Once you have captured the reboot, please send us a copy of your system log on the following email address support@billion.uk.com or submit a ticket on the following link http://www.billion.uk.com/esupport/inde ... ets/Submit

It has just rebooted with UPNP turned off so doesn't appear to be the cause.

I don't have a windows machine at hand and although I could go through the hassle of sorting this out I'd prefer a quicker fix if possible.

I've tried to downgrade the firmware (in the hope that might help) to the one mentioned on this forum a few times (2.32d dh65) but I get the following error:

Image uploading failed. The selected file contains an illegal image.

Is that firmware suitable for the 8800nl R2 or am I getting the wrong one? I got it from the forum here a few posts down.

Here are the latest logs:

Jan 1 00:00:15 kern info kernel: Initializing WLCSM Module
Jan 1 00:00:15 kern info kernel: WLCSM Module loaded successfully
Jan 1 00:00:15 kern warn kernel: brcmchipinfo: brcm_chipinfo_init entry
Jan 1 00:00:15 kern warn kernel: bcmxtmrt: Broadcom BCM3381B0 ATM/PTM Network Device v0.9 Dec 22 2016 13:42:50
Jan 1 00:00:15 kern warn kernel: Broadcom Ingress QoS Module Char Driver v0.1 Dec 22 2016 13:42:42 Registered<243>^[[0m
Jan 1 00:00:15 kern warn kernel: Broadcom Ingress QoS ver 0.1 initialized
Jan 1 00:00:15 kern warn kernel: BPM: tot_mem_size=67108864B (64MB), buf_mem_size <15%> =10066320B (9MB), num of buffers=4993, buf size=2016
Jan 1 00:00:15 kern warn kernel: Broadcom BPM Module Char Driver v0.1 Dec 22 2016 13:42:40 Registered<244>^[[0m
Jan 1 00:00:15 kern warn kernel: NBUFF v1.0 Initialized
Jan 1 00:00:15 kern warn kernel: ^[[0;36;44mInitialized fcache state^[[0m
Jan 1 00:00:15 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache Char Driver v3.0 Dec 22 2016 13:42:42 Registered<242>^[[0m
Jan 1 00:00:15 kern warn kernel: Created Proc FS /procfs/fcache
Jan 1 00:00:15 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache registered with netdev chain^[[0m
Jan 1 00:00:15 kern warn kernel: ^[[0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.^[[0m
Jan 1 00:00:15 kern warn kernel: flwStatsThread created
Jan 1 00:00:15 kern warn kernel: ^[[0;36;44mConstructed Broadcom Packet Flow Cache v3.0 Dec 22 2016 13:42:42^[[0m
Jan 1 00:00:15 kern warn kernel: Allocated EXT_TIMER number 3
Jan 1 00:00:15 kern warn kernel: Broadcom Traffic Manager (bcmtm) Char Driver v0.1 Dec 22 2016 13:42:45 Registered <229>
Jan 1 00:00:15 kern warn kernel: bcmxtmcfg: bcmxtmcfg_init entry
Jan 1 00:00:15 kern warn kernel: adsl: adsl_init entry
Jan 1 00:00:15 kern warn kernel: Broadcom BCM63381B0 Ethernet Network Device v0.1 Dec 22 2016 13:42:48
Jan 1 00:00:15 kern warn kernel: ETH Init: Ch:0 - 200 tx BDs at 0xa3b31000
Jan 1 00:00:15 kern warn kernel: ETH Init: Ch:0 - 1997 rx BDs at 0xa2b20000
Jan 1 00:00:15 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
Jan 1 00:00:15 kern warn kernel: eth0: <Int sw port: 0> <Logical : 00> PHY_ID <0x00000001 : 0x01> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth1: <Int sw port: 1> <Logical : 01> PHY_ID <0x00000002 : 0x02> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth2: <Int sw port: 2> <Logical : 02> PHY_ID <0x00000003 : 0x03> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth3: <Int sw port: 3> <Logical : 03> PHY_ID <0x00000004 : 0x04> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: eth4: <Int sw port: 4> <Logical : 04> PHY_ID <0x05980018 : 0x18> MAC : 60:03:47:2E:D5:21
Jan 1 00:00:15 kern warn kernel: Ethernet Auto Power Down and Sleep: Enabled
Jan 1 00:00:15 kern warn kernel: All Port Bit Map: 0x001f: eth0,eth1,eth2,eth3,eth4
Jan 1 00:00:15 kern warn kernel: Chip WAN Only Ports 0000, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0000:
Jan 1 00:00:15 kern info kernel: NComm TMS V6.80 Kernel Module loaded.
Jan 1 00:00:15 kern warn kernel: --SMP support
Jan 1 00:00:15 kern warn kernel: wl: dsl_tx_pkt_flush_len=338
Jan 1 00:00:15 kern warn kernel: wl: norm_wmark_tot=1417, pktc_wmark_tot=1417
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
Jan 1 00:00:15 kern warn kernel: wl: passivemode=1
Jan 1 00:00:15 kern info kernel: wl0: creating kthread wl0-kthrd
Jan 1 00:00:15 kern warn kernel: wl: napimode=0
Jan 1 00:00:15 kern warn kernel: initvars_cis_pci: Not CIS format
Jan 1 00:00:15 kern warn kernel: Neither SPROM nor OTP has valid image
Jan 1 00:00:15 kern warn kernel: wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
Jan 1 00:00:15 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:15 kern warn kernel: wl: ID=pci/2/0/
Jan 1 00:00:15 kern warn kernel: wl: loading /etc/wlan/bcm43217_map.bin
Jan 1 00:00:15 kern warn kernel: srom rev:8
Jan 1 00:00:15 kern warn kernel: wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32
Jan 1 00:00:15 kern warn kernel: wl0: allocskbmode=1 currallocskbsz=256
Jan 1 00:00:15 kern warn kernel: wl0: Broadcom BCM43227 802.11 Wireless Controller 7.14.131.1608.cpe4.16L05.0-kdb
Jan 1 00:00:15 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Jan 1 00:00:15 kern info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
Jan 1 00:00:15 kern debug kernel: ehci_hcd 0000:00:0a.0: setting latency timer to 64
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: EHCI Host Controller
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
Jan 1 00:00:15 kern warn kernel: ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: irq 113, io mem 0x1000c300
Jan 1 00:00:15 kern info kernel: ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
Jan 1 00:00:15 kern info kernel: hub 1-0:1.0: USB hub found
Jan 1 00:00:15 kern info kernel: hub 1-0:1.0: 1 port detected
Jan 1 00:00:15 kern info kernel: ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan 1 00:00:15 kern warn kernel: PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
Jan 1 00:00:15 kern debug kernel: ohci_hcd 0000:00:09.0: setting latency timer to 64
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: OHCI Host Controller
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
Jan 1 00:00:15 kern info kernel: ohci_hcd 0000:00:09.0: irq 112, io mem 0x1000c400
Jan 1 00:00:15 kern info kernel: hub 2-0:1.0: USB hub found
Jan 1 00:00:15 kern info kernel: hub 2-0:1.0: 1 port detected
Jan 1 00:00:15 kern info kernel: usbcore: registered new interface driver usblp
Jan 1 00:00:15 kern info kernel: Initializing USB Mass Storage driver...
Jan 1 00:00:15 kern info kernel: usbcore: registered new interface driver usb-storage
Jan 1 00:00:15 kern info kernel: USB Mass Storage support registered.
Jan 1 00:00:15 kern info kernel: Broadcom 802.1Q VLAN Interface, v0.1
Jan 1 00:00:15 kern warn kernel: brcm_otp_init entry
Jan 1 00:00:15 kern warn kernel: Host MIPS Clock divider pwrsaving is enabled
Jan 1 00:00:15 kern info kernel: Netfilter messages via NETLINK v0.30.
Jan 1 00:00:16 kern warn kernel: br_netlink_mcpd.c: Setting registration type 0 pid to 431
Jan 1 00:00:17 kern info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:17 kern info kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 00:00:18 kern info kernel: device eth0 entered promiscuous mode
Jan 1 00:00:18 kern info kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 1 00:00:21 kern info kernel: device eth1 entered promiscuous mode
Jan 1 00:00:21 kern info kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 1 00:00:24 kern info kernel: device eth2 entered promiscuous mode
Jan 1 00:00:24 kern info kernel: ADDRCONF(NETDEV_UP): eth2: link is not ready
Jan 1 00:00:28 kern info kernel: device eth3 entered promiscuous mode
Jan 1 00:00:28 kern info kernel: ADDRCONF(NETDEV_UP): eth3: link is not ready
Jan 1 00:00:31 kern info kernel: device eth4 entered promiscuous mode
Jan 1 00:00:31 kern info kernel: ADDRCONF(NETDEV_UP): eth4: link is not ready
Jan 1 00:00:34 kern warn kernel: *** dslThread dslPid=893
Jan 1 00:00:34 kern warn kernel: BcmAdsl_Initialize=0xC01AD050, g_pFnNotifyCallback=0xC01E8B60
Jan 1 00:00:34 kern warn kernel: DYING GASP IRQ Disabled
Jan 1 00:00:34 kern warn kernel: DYING GASP IRQ Enabled
Jan 1 00:00:34 kern warn kernel: AdslCoreSetSdramImageAddr: lmem2(0xce000) vs ADSL_PHY_SDRAM_BIAS(0xce000); origAddr=0xA3ECE000 newAddr=0xA3ECE000
Jan 1 00:00:34 kern warn kernel: pSdramPHY=0xA3FFFFF8, 0x1B777E 0xDEADBEEF
Jan 1 00:00:34 kern warn kernel: *** XfaceOffset: 0x4FF90 => 0x4FF90 ***
Jan 1 00:00:35 kern warn kernel: *** PhySdramSize got adjusted: 0xF5FB4 => 0x129AB8 ***
Jan 1 00:00:35 kern warn kernel: AdslCoreSharedMemInit: shareMemSize=34080(34080)
Jan 1 00:00:35 kern warn kernel: AdslCoreHwReset: pLocSbSta=80c60000 bkupThreshold=3072
Jan 1 00:00:35 kern warn kernel: AdslCoreHwReset: AdslOemDataAddr = 0xA3FB59A4, time=11 ms
Jan 1 00:00:35 kern warn kernel: VersionInfo: A2pvI042j1.d26m
Jan 1 00:00:35 kern warn kernel: ***BcmDiagsMgrRegisterClient: 0 ***
Jan 1 00:00:35 kern warn kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Jan 1 00:00:35 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = DISABLED
Jan 1 00:00:35 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Jan 1 00:00:35 kern warn kernel: XTM Init: Ch:0 - 499 rx BDs at 0xa0d00000
Jan 1 00:00:35 kern warn kernel: XTM Init: Ch:1 - 16 rx BDs at 0xa345c480
Jan 1 00:00:35 kern warn kernel: bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
Jan 1 00:00:35 kern warn kernel: bcmxtmcfg: Out of sequence call to XTM_ASM_HANDLER::Uninitialize(). Recovering.
Jan 1 00:00:35 kern warn kernel: bcmxtmcfg: ATM Bonding configured in system. Fallback mode = Enabled
Jan 1 00:00:35 kern warn kernel: bcmxtmcfg: Bonding State is DATA_IDLE
Jan 1 00:00:35 kern warn kernel: bcmxtmcfg: SID MODE SET to 12 BIT MODE
Jan 1 00:00:35 kern warn kernel: bcmxtmcfg: ATM Bonding Mgmt Log Area = 80702518
Jan 1 00:00:35 kern info kernel: nf_conntrack version 0.5.0 (917 buckets, 3668 max)
Jan 1 00:00:36 kern info kernel: xt_time: kernel timezone is -0000
Jan 1 00:00:37 kern info kernel: message received before monitor task is initialized kerSysSendtoMonitorTask
Jan 1 00:00:38 kern info kernel: monitor task is initialized pid= 378
Jan 1 00:00:39 kern warn kernel: Energy Efficient Ethernet: Enabled
Jan 1 00:00:43 user info syslog: WLAN Schedule Control on wl0 exit
Jan 1 00:00:43 kern crit kernel: eth4 (Int switch port: 4) (Logical Port: 4) Link UP 1000 mbps full duplex
Jan 1 00:00:43 kern info kernel: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready
Jan 1 00:00:43 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:00:43 kern info kernel: br0: port 5(eth4) entered forwarding state
Jan 1 00:01:00 kern crit kernel: Line 0: VDSL G.993 channel analysis
Jan 1 00:01:00 kern crit kernel: Line 0: VDSL2 link up, Bearer 0, us=6678, ds=35000
Jan 1 00:01:00 kern crit kernel: Line 0: VDSL2 link up, Bearer 1, us=0, ds=0
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: SILI Start - UtopiaCfg - 0
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: DS xDSL G.inp Mode = ENABLED
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: xDSL G.Fast Mode = DISABLED
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: XTM Link Information, port = 0, State = UP(1), Service Support = PTM(2)
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: ReconfigureSAR port 0 traffictype 2
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: Normal(XTM/PTM) Mode enabled
Jan 1 00:01:00 kern warn kernel: bcmxtmcfg: SILI End - UtopiaCfg - 10
Jan 1 00:01:01 kern warn kernel: bcmxtmrt: TxPAF Status = Disabled
Jan 1 00:01:01 kern warn kernel: bcmxtmrt: MAC address: 60 03 47 2e d5 23
Jan 1 00:01:01 kern warn kernel: [DoCreateDeviceReq.775]: register_netdev
Jan 1 00:01:01 kern warn kernel: [DoCreateDeviceReq.777]: register_netdev done
Jan 1 00:01:01 kern warn kernel: bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0
Jan 1 00:01:01 kern warn kernel: NON-CO4 DSLAM based operations for PTM CRC & ENET FCS.
Jan 1 00:01:01 kern warn kernel: XTM Init: Ch:0 - 400 tx BDs at 0xa1720000
Jan 1 00:01:01 kern warn kernel: bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=6678000, DS=35000000
Jan 1 00:01:01 kern warn kernel: ptm0.1 MAC address set to 60:03:47:2E:D5:24
Jan 1 00:01:01 kern warn kernel: netdev path : ptm0.1 ->
Jan 1 00:01:01 kern info kernel: ptm0
Jan 1 00:01:01 kern warn kernel: BCMVLAN : ptm0 mode was set to RG
Jan 1 00:01:01 kern info kernel: device ptm0 entered promiscuous mode
Jan 1 00:01:01 daemon notice syslog: pppd:cms logging initialized.
Jan 1 00:01:01 daemon notice syslog: pppd 2.4.1 started by admin, uid 0
Jan 1 00:01:01 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:24 daemon err syslog: pppd:Couldn't get channel number: Transport endpoint is not connected
Jan 1 00:01:24 daemon notice syslog: pppd:Couldn't reset tty to normal line discipline: Inappropriate ioctl for device
Jan 1 00:01:24 daemon notice syslog: pppd:Doing disconnect
Jan 1 00:01:27 daemon notice syslog: PPP: Start to connect ...
Jan 1 00:01:27 daemon crit syslog: PPP server detected.
Jan 1 00:01:27 daemon crit syslog: PPP session established.
Jan 1 00:01:27 kern warn kernel: netdev path : ppp1.1 ->
Jan 1 00:01:27 kern info kernel: ptm0.1 ->
Jan 1 00:01:27 daemon notice syslog: pppd:Using interface ppp1.1
Jan 1 00:01:27 daemon notice syslog: pppd:Connect: ppp1.1 <--> ptm0.1
Jan 1 00:01:27 kern info kernel: ptm0
Jan 1 00:01:27 daemon notice syslog: pppd:Couldn't increase MTU to 1500.
Jan 1 00:01:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:27 daemon err syslog: pppd:Couldn't increase MRU to 1500
Jan 1 00:01:27 daemon crit syslog: PPP LCP UP.
Jan 1 00:01:27 daemon notice syslog: pppd:Warning - secret file /etc/ppp/chap-secrets has world and/or group access
Jan 1 00:01:27 daemon notice syslog: pppd:No CHAP secret found for authenticating us to acc-aln6.tw
Jan 1 00:01:27 daemon notice syslog: pppd:Remote message: CHAP authentication success
Jan 1 00:01:27 daemon notice syslog: pppd:local IP address 5.80.237.189
Jan 1 00:01:27 daemon notice syslog: pppd:remote IP address 172.16.10.5
Jan 1 00:01:27 daemon notice syslog: pppd:primary DNS address 81.139.56.100
Jan 1 00:01:27 daemon notice syslog: pppd:secondary DNS address 81.139.57.100
Jan 1 00:01:27 daemon crit syslog: Received valid IP address from server. Connection UP.
Mar 2 13:23:13 user info syslog: ddnsd: xxxxx.ddns.net (ppp1.1) IP has changed from (null) to 5.80.237.189
Mar 2 13:23:14 user info syslog: ddnsd: update xxxxx.ddns.net request successfully
Mar 2 13:31:45 daemon info syslog: Firmware tag product Id [8800NL] is not compatible with the current Tag product Id. cur-product Id [8800NLR2]
Mar 2 13:33:26 daemon info syslog: Firmware tag product Id [8800NL] is not compatible with the current Tag product Id. cur-product Id [8800NLR2]
Mar 2 13:36:04 daemon info syslog: Firmware tag product Id [8800NL] is not compatible with the current Tag product Id. cur-product Id [8800NLR2]

Try using the firmware on the attached link

http://www.billion.uk.com/esupport/inde ... on-250ad13

2.32d.dh65 is for the 8800NL not the 8800NL R2