You must use a computer using an Ethernet (yellow) cable that is hard wired to the 7 series Router to set up the wireless security. You should never use a wireless client connected to the router to set up any type of wireless security. Launch the Interne...
You must use a computer using an Ethernet (yellow) cable that is hard wired to the 5200G to set up the wireless security. You should never use a wireless client connected to the router to set up any type of wireless security. Launch the Internet browser....
You must use a computer using an Ethernet (yellow) cable that is hard wired to the 7 series Router to set up the wireless security. You should never use a wireless client connected to the router to set up any type of wireless security. Launch the Inter...
WMM stand for WiFi Multimedia.It is a Wi-Fi Alliance interoperability certification, based on the Institute of Electrical and Electronics Engineers 802.11e standard. It provides basic Quality of service (QoS) features to IEEE 802.11 networks. WMM prioriti...
A single channel is 20MHz in width. When two channels are bonded they are a total of 40MHz. It is possible to use either 20MHz or 40MHz channels with IEEE 802.11n. The Channel bonding trick can provide a 10 to 20 Mbps throughput increase, but usually work...
It is know most 802.11n products will only connect at 54Mbps if you use WEP or WPA/TKIP security. The reason being that the 802.11n specification states that the high throughput rates (link rates above 54Mbps) can't be enabled if either of those outdated ...
First assign an IP address to your computer (i.e 192.168.1.10). Lauch
the Internet browser then type 192.168.1.253 in (2073N's default IP
address) in the URL box, then press Enter on your keyboard. When
prompt enter Username 'Admin' and Password 'admin...
You can enhance your wireless security by enable the wireless mac
filter feature. Please follow the instruction below.
1. First you can add the trusted computer/device's MAC address to the
list.
2. A client has added to the filter list.
3. Onc...
You can set up the wireless security first on the 3100SN. Use an
Ethernet cable to establish a connection in between your computer and
the 3100SN. You need to assign an IP address to your computer, before
you can reach the 3100SN's web GUI (192.168.1.2...
WDS (Wireless Distribution System) that enables the wireless
interconnection of AP (Access Point) in an IEEE 802.11 network.
It will allow a wireless network to be expanded using multiple access
points without the need for a wired backbone to link them, ...
Below is how to change the ESSID and the radio channel. Remember to save the settings.
You
must use a computer using an Ethernet (yellow) cable that is hard wired
to the 7 series Router to set up the wireless security. You should
never use a wireless client connected to the router to set up any type
of wireless security. Launch the...
Yes, your 802.11n enabled router can also work with 802.11g and even 11b devices at the same time. But
these much slower devices force the router to slow down to talk to them,
which means a big throughput hit. Fortunately, the "legacy" mecha...
WDS ｉｓ ｑｕｉｔｅ ｅａｓｙ ｔｏ ｓｅｔ ｕｐ．
１）． Ｓａｍｅ ｒａｄｉｏ ｃｈａｎｎｅｌ
２）． Ｓａｍｅ ｗｉｒｅｌｅｓｓ ｓｅｃｕｒｉｔｙ （ｉｆ ｗｉｒｅｌｅｓｓ ｓｅｃｕｒｉｔｙ ｉｓ ｉｎ ｕｓｅ）．
３）． Enａｂｌｅ ＷＤＳ ｏｎ ｂｏｔｈ ｄｅｖｉｃｅｓ
４）． Ｅｎｔｅｒ ｔｈｅ ＭＡＣ ａｄｄｒｅｓｓ ｏｆ ｔｈｅ ｏｐｐｏｓｉｔ ｄｅｖｉｃｅ．
Ｆｉｒｓｔ ｗｅ ｃｏｎｆｉｇｕｒｅ ｔｈｅ ７８００Ｎ．
Ａｎｄ ｔｈｅｎ ｓａ...
